Decor "Barashek"

Decor "Barashek"

DECOR
DECORATIVE PLASTER "BARASHEK"  FOR INDOOR AND OUTDOOR USE 

  • Expressive stone texture
  • Resistant to shock
  • Weatherproof
  • Crack resistant
  • Easy to use
  • Aggregate size - 1.5 and 2.0 mm - empty
  • Freeze proof
  • Vapor permeable
  • Energy efficient
 
Quality Certificate:

CE
EN 998-1:2010
EN 998-1-GP-CSIV-W0


Dry building mix  ТМ MASTER C1.SHT4 DSTU B V.2.7-126:2011

Bar-code:

Filler 1.5 mm – 4820086 382212

Filler 2.4 mm – 4820086 382229


Video

25 kg

Dry building mix for plastering ТМ MASTER. DECOR. DECORATIVE PLASTER "BARASHEK" is designed for decorating concrete, brick, and cement-sandy plastered bases inside and outside of buildings; used in thermal insulation systems as the decorative and protective layer. For indoor and outdoor use

SURFACE PREPARATION

Surface preparation must be done in accordance with the State Building Standard of Ukraine DBN V.2.6-22-2001. The base must be:

- clean (remove dirt, flows, dust, fungal lesions with a power tool or manually, also clean from residual oils and paints);

- strong (not lower than the coating strength);

- dry (moisture content less than 4%);

- in presence of cracks (to be grouted), drops or irregularities treat the base with ТМ MASTER, and then align with the mineral mix for plastering, for example ТМ MASTER. FRONT. Sandy White (48 hours before the start of work);

- to enhance contact with the mix, treat the surface for plastering with the primer ТМ MASTER (4 hours before the start of work);

- bases with fungal lesions must be treated with the antifungal primer ТМ MASTER. Antifungal.

 

WORK PROCEDURE

Perform the work at an air temperature of +50С to +300С. The temperature of the base must be in the same range. Two days before the start of plastering, in the process of its performance, and for three days after the end maintain the temperature indoors not below +50Сand not above +300С.

Add pure water to the dry mix in an amount indicated in specifications, then mix it (use electric drills with screw socket). Leave closed mix for 5 minutes, and then stir again. The closed mix is suitable for use within 120 minutes (at recommended atmospheric conditions). Apply the stirred mix ТМ MASTER. DECOR. DECORATIVE PLASTER "BARASHEK" on the surface with a trowel or a float.  The thickness of the layer applied must meet the filler aggregate size. Plastering must be conducted continuously, apply and join each new site until the solidification of the previous one.

Apply the paint no earlier than 48 hours after the plastering work.

NOTE TO A BUYER

- The base strength must be not less than the strength of the mix;

- Failure to follow the instructions for use mentioned on the package may adversely affect the aesthetic and performance properties;

- Products are not subject to mandatory certification;

- The mix is safe for human health in the production, transportation, storage, application and during the operation subject to following the requirements of this standard to production safety and health;

- Keep away from children;

- Date of manufacture, shelf life and batch number are mentioned on the package;

- Use only for the intended purpose.

- The manufacturer is not responsible for the use of the material for the purpose and under conditions not covered by this instruction.

- This instruction is a recommendation and does not substitute the professional training of the contractor.

Dry building mix  ТМ MASTER C1.SHT4 DSTU B V.2.7-126:2011

Ingredients

Cement mix modified with mineral fillers and polymeric additives

Aggregate size

1.5 (2.0) mm

Time the closed mix is suitable for use

120 minutes

Open time

20 minutes

Recommended amount of water for preparing the mix

0.20-0.21 L / 1 kg of mix

Operation temp.

5ºС to +30ºС

Consumption

3.2 (3.8)* kg/m2

* For a fraction of 2.0 mm

All of these recommendations are efficient at +20С and relative humidity of 60%.

SAFETY RULES

Dry building mixture contains cement, which causes alkaline reaction in hydration. When using the mix, use the personal protective equipment (respirator and rubber gloves). When working, protect the skin and eyes. In case of a mixture contact with eyes, rinse them immediately with plenty of water and seek medical advice.

Expiration date: 12 months from the date of manufacture mentioned on the package.

Must be disposed of in accordance the State Standard of Ukraine DSanPiN 2.2.7.029

Storage conditions: Store in the original intact packaging, on pallets, in dry premises at temperatures below 400С and humidity of 75%.

Warranty period: The manufacturer guarantees compliance of the quality with the requirements of this standard for the period specified on the package, provided the requirements of transport and storage are followed.