Isopro

Isopro

ISOPRO

UNIVERSAL GYPSUM PLASTER FOR SURFACE LEVELING AND REPAIR

 

  • Thermal insulation and sound-proof
  • Plastic and crack resistant
  • Easy to use
  • Resistant to abrasion and shrinkage
  • No slipping from surfaces
  • Suitable for leveling ceilings
  • Aggravates microclimate in rooms 
  • Layer thickness of 3-50 mm                                  
  • Vapor permeable                                        
  • With perlite
  • White Can be troweled to gloss

Quality Certificate:

CE

EN 13279-1:2008

EN 13279-1-B5/50/2


Dry building mix ТМ MASTER G.2.SHT6 white DSTU B V.2.7-126:2011

Bar-code: 4820086382250

30 kg
Universal dry modified building gypsum mix ТМ MASTER. ISOPRO designed for treatment of concrete, brick, cement, sand, and plaster surfaces inside buildings. Used for pre-alignment of walls and ceilings for subsequent application of wallpaper or painting. 

SURFACE PREPARATION

Surface preparation must be done in accordance with the State Building Standard of Ukraine DBN V.2.6-22-2001. The base must be:

- clean (remove dirt, flows, dust, fungal lesions with a power tool or manually);

- strong (not lower than the coating strength);

- dry (moisture content less than 4%);

- to enhance contact with the mix, treat the surface with the primer ТМ MASTER or ТМ іMASTER;

- to reduce water absorption, treat the surface with the primer paint ТМ MASTER. CONTACT (3 hours before the start of work);

 

INSTRUCTIONS FOR USE

Perform the work at air and surface base temperature of +100С to +300С, and the humidity no higher than 70%. The result will be efficient at +200С and relative humidity of 60%. In other conditions features may vary. Particular attention must be paid to the humidity in the room - the gypsum mix is used in dry environmental conditions. Two days before the start of work, in the process of its performance, and for three days after the end maintain the temperature and humidity indoors not above the specified ones.

Add pure water to the dry mixture in an amount indicated in specifications, then mix it (use electric drills with screw socket). Leave closed mix for 5 minutes, and then stir again. The closed mix is suitable for use within 60 minutes (at recommended atmospheric conditions). Apply the closed mix ТМ MASTER. ISOPRO on the surface with a trowel, float or leveling plate. Plastering must be performed continuously by wet-on-wet method.

When arranging multilayer plaster coating, each subsequent layer must be applied after previous solidification. The applied layer must be evened before the beginning of the closed mix solidification.

In order to get the surface for painting, diligently wipe the surface with a damp metal grater before the solidification process begins.

Perform grinding of the leveling layer surface and further painting and wallpapering  not earlier than 24 hours after applying the last layer of mix.

NOTE TO A BUYER

- The base strength must be not less than the strength of the mix;

- Failure to follow the instructions for use mentioned on the package may adversely affect the aesthetic and performance properties;

- Products are not subject to mandatory certification;

- The mix is safe for human health in the production, transportation, storage, application and during the operation subject to following the requirements of this standard to production safety and health;

- Keep away from children;

- Date of manufacture, shelf life and batch number are mentioned on the package;

- Use only for the intended purpose.

- The manufacturer is not responsible for the use of the material for the purpose and under conditions not covered by this instruction.

- This instruction is a recommendation and does not substitute the professional training of the contractor.          

Dry building mix ТМ MASTER G.2.SHT6 white DSTU B V.2.7-126:2011
 

Ingredients

Mix of gypsum and mineral fillers, modified by polymeric and thermal insulation additives

Size of aggregate, maximum

0.63 mm

Time the closed mix is suitable for

60 minutes

Strength of adhesion to base

0.4 MPa

Limit strength in compression

3 MPa

Recommended layer thickness

3 - 50 mm

Recommended amount of water for preparing the mix

0.3 – 0.4 L / 1 kg

Consumption

1 kg / m2 / 1 mm

All of these recommendations are efficient at 200С and relative humidity of 60%.

SAFETY RULES

When using the mix, use the personal protective equipment (respirator and rubber gloves). When working, protect the skin and eyes. In case of a mixture contact with eyes, rinse them immediately with plenty of water and seek medical advice.

Expiration date: 12 months from the date of manufacture mentioned on the package.

Must be disposed of in accordance the State Standard of Ukraine DSanPiN 2.2.7.029

Storage conditions: Store in the original intact packaging, on pallets, in dry premises at temperatures below 400С and humidity of 75%.

Warranty period: The manufacturer guarantees compliance of the quality with the requirements of this standard for the period specified on the package, provided the requirements of transport and storage are followed.