Armir

Armir

ARMIR REINFORCEMENT MIX FOR POLYSTYRENE

  • Robust insulation system
  • High adhesion to polystyrene bases
  • Resistant to shock
  • Highly plastic and easy to use
  • Weatherproof and permeable
  • High strength
  • Waterproof
  • Freeze proof
  • Energy efficient

Quality Certificate:
CE 
EN 998-1:2010
EN 998-1-GP-CSIII-W0

Dry building mix  ТМ MASTER C1.ЗК5 DSTU B V.2.7-126:2011

Bar-code  4820086 381185

25 kg +/-1%
Dry building reinforcement  mix for polystyrene ТМ MASTE. ARMIR designed for making a reinforcing layer for external heat insulation systems of buildings.

SURFACE PREPARATION
Surface preparation must be done in accordance with the State Building Standard of Ukraine DBN V.2.6-22-2001. The base must be:
- clean (remove dirt, flows, dust, fungal lesions with a power tool or manually, also clean from residual oils and paints);
- strong (remove all loose areas and process them with the primer ТМ MASTER or іMASTER;
- align significant irregularities in bases using the plaster or adhesive mixes for thermal insulation systems ТМ MASTER or ТМ іMASTER.

WORK PROCEDURE
Perform the work at an air temperature of +50С to +250С. The temperature of the base must be in the same range. Facades must be protected from direct sunlight, wind and precipitation.
Add pure water to the dry mixture in an amount indicated in specifications, then mix it (use electric drills with screw socket). Leave closed mix for 5 minutes, then stir again. The closed mix is suitable for use within 120 minutes (at recommended atmospheric conditions). At high temperatures, periodically stir the closed mix to avoid reducing its mobility.
Apply the closed mix ТМ MASTER. ARMIR the surface of the polystyrene with a layer thickness of 2-3 mm using a trowel or other tools. In a layer applied, evenly and without tension insert the reinforcing mesh ТМ MASTER. Apply on the mesh the next layer with a thickness of 3-4 mm.
Apply the decorative protective layer 72 hours after the surface; before this, treat the surface with the quartz primer paint ТМ MASTER. CONTACT.

NOTE TO A BUYER

  • The base strength must be not less than the strength of the mix;
  • Failure to follow the instructions for use mentioned on the package may adversely affect the aesthetic and performance properties;
  • Products are not subject to mandatory certification;
  • The mix is safe for human health in the production, transportation, storage, application and during the operation subject to following the requirements of this standard to production safety and health;
  • Keep away from children;
  • Date of manufacture, shelf life and batch number are mentioned on the package;
  • Use only for the intended purpose.
  • The manufacturer is not responsible for the use of the material for the purpose and under conditions not covered by this instruction.
  • This instruction is a recommendation and does not substitute the professional training of the contractor.



Dry building mix  ТМ MASTER C1.ЗК5 DSTU B V.2.7-126:2011

Ingredients

Cement-sand mix, modified with polymeric additives and reinforcing micro fiber

Size of aggregate, maximum

0,8 mm

Time the closed mix is suitable for

120 minutes

Open time

10 minutes

Max compressive strength

7 Mpa

Recommended amount of water for preparing the mix

0,21 – 0,23 L/kg

(5,25 – 5,75 L/25 кг)

Application temperature

+5°C to +25°C

Frost resistance, min

50 cycles

Consumption

1.45 kg / m2 / 1 mm

All of these recommendations are efficient at +20°С and relative humidity of 60%.


SAFETY RULES

Dry building mixture contains cement, which causes alkaline reaction in hydration. When using the mix, use the personal protective equipment (respirator and rubber gloves). When working, protect the skin and eyes. In case of a mixture contact with eyes, rinse them immediately with plenty of water and seek medical advice.

Expiration date: 12 months from date of manufacturing in original packaging in a dry place.

Storage conditions:
Store in the original intact packaging, on pallets, in dry premises at temperatures below +40°С and humidity of 75%.


Warranty period:
The manufacturer guarantees compliance of the quality with the requirements of this standard for the period specified on the package, provided the requirements of transport and storage are followed.