Carcass

Carcass

 

CARCASS

 

ADHESIVE MIX FOR MASONRY

 

FOR GAS CONCRETE AND FOAM CONCRETE BLOCKS

 

  • Ideal for making of gas concrete partition walls
  • Suitable for brickwork!
  • Ideal for plastering surfaces of blocks
  • High adhesion capacity
  • High adhesion to any base
  • Plastic
  • Masonry: 2-6 mm thickness
  • Freeze proof
  • Vapor permeable


Quality Certificate:
CE
EN  998-2:2010 T-M5

Dry building mix ТМ MASTER C1.MR2 DSTU B V.2.7-126:2011

Bar-code: 4820086381352 




25 kg +/-1%

Modified dry building mix ТМ MASTER.CARCASS» designed for laying wall blocks from porous concrete, lightweight concrete, silicate, limestone; masonry; making concrete partition walls; plastering surface of blocks inside and outside buildings.

SURFACE PREPARATION

Surface preparation must be done in accordance with the State Building Standard of Ukraine DBN V.2.6-22-2001. The base must be:

- clean (remove dirt, flows, dust, fungal lesions with a power tool or manually, also clean from residual oils and paints);

- strong (not lower than the coating strength);

- If the surface has high water absorption and to enhance contact with the mix, treat the base with high absorptive capacity with the primer ТМ MASTER or ТМ іMASTER (4 hours before the start of work);

 

INSTRUCTIONS FOR USE

Perform the work at an air temperature of +50С to +350С. The temperature of the base must be in the same range.

Add pure water to the dry mixture in an amount indicated in specifications, then mix it (use electric drills with screw socket). Leave closed mix for 5 minutes, then stir again. The closed mix is suitable for use within 180 minutes (at recommended atmospheric conditions). At high temperatures, periodically stir the closed mix to avoid reducing its mobility.

Apply the prepared mix ТМ MASTER. CARCASS on the surface of blocks being joined, with a spattel or other tools. Blocks can be adjusted for 5-10 minutes with a rubber hammer.

Defects in a porous block should be removed using the prepared mix ТМ MASTER. CARCASS, creating a monolithic structure.


NOTE TO A BUYER

- The base strength must be not less than the strength of the mix;

- Failure to follow the instructions for use mentioned on the package may adversely affect the aesthetic and performance properties;

- Products are not subject to mandatory certification;

- The mix is safe for human health in the production, transportation, storage, application and during the operation subject to following the requirements of this standard to production safety and health;

- Keep away from children;

- Date of manufacture, shelf life and batch number are mentioned on the package;

- Use only for the intended purpose.

- The manufacturer is not responsible for the use of the material for the purpose and under conditions not covered by this instruction.

- This instruction is a recommendation and does not substitute the professional training of the contractor.

Dry building mix ТМ MASTER C1.MR2 DSTU B V.2.7-126:2011

Ingredients                                                                     

Mix of cement and mineral fillers, modified by polymeric additives

Size of aggregate, maximum

0.8 mm

Time the closed mix is suitable for                     

180 minutes

Adjustment time                                              

5 minutes

Strength of adhesion to base                                             

0.5MPa

Max compressive strength                                                            

5 MPa

Layer thickness                   

2 - 6 mm

Recommended amount of water for preparing the mix                                     

0.19 - 0.21 L / 1 kg

Application temperature                              

+5ºС to +30ºС

Operation temperature   

-40ºС to +70ºС

Consumption

1.3 kg / m2 / 1 mm

All of these recommendations are efficient at +200С and relative humidity of 60%.

SAFETY RULES

Dry building mixture contains cement, which causes alkaline reaction in hydration. When using the mix, use the personal protective equipment (respirator and rubber gloves). When working, protect the skin and eyes. In case of a mixture contact with eyes, rinse them immediately with plenty of water and seek medical advice.

Expiration date: 12 months from the date of manufacture mentioned on the package.

Must be disposed of in accordance the State Standard of Ukraine DSanPiN 2.2.7.029

Storage conditions: Store in the original intact packaging, on pallets, in dry premises at temperatures below +400С and humidity of 75%.

Warranty period: The manufacturer guarantees compliance of the quality with the requirements of this standard for the period specified on the package, provided the requirements of transport and storage are followed.