Satenpro

Satenpro

SATENPRO

INTERIOR FINISHING GYPSUM PLASTER

  • Fine - filler particle size less than 0.3 mm
  • Can be troweled to gloss without dust at work
  • High-quality alignment
  • Possibility to create textured surfaces
  • Efficient and easy to use
  • No slipping from surfaces
  • Aggravates microclimate in rooms
  • Fireproof
  • Plastic                                               
  • Layer thickness up to 3-50 mm                             
  • Vapor permeable                 
  • White

Quality Certificate:

CE

EN 13279-1:2008

EN 13279-1-B2/50/2

Dry building mix ТМ MASTER GV.SHG1 white DSTU B V.2.7-126:2011

Bar-code: 4820086382298

 

Benefits:

орапглагнашн
25 kg +/-1%

Dry gypsum modified building mix for plastering ТМ MASTER. SATENPRO designed to prepare concrete, brick and plastered surfaces inside buildings for various finishing and painting (thickness - up to 10 mm); ideally aligns plastered surfaces. Used in rooms with normal humidity. For internal use

SURFACE PREPARATION

Surface preparation must be done in accordance with the State Building Standard of Ukraine DBN V.2.6-22-2001. The base must be:

- clean (remove dirt, flows, dust, fungal lesions with a power tool or manually);

- strong (not lower than the coating strength);

- dry (moisture content less than 4%);

- in presence of cracks, cavities and irregularities align the base with ТМ MASTER (24 hours before the start of work);

- to enhance contact with the mix, treat the surface for plastering with the primer ТМ MASTER or ТМ іMASTER;

 

INSTRUCTIONS FOR USE

Perform the work at air and surface base temperature of +100С to +300С, and the humidity no higher than 70%. The result will be efficient at +200С and relative humidity of 60%. In other conditions features may vary. Particular attention must be paid to the humidity in the room - the gypsum mix is used in dry environmental conditions. Two days before the start of work, in the process of its performance, and for three days after the end maintain the temperature and humidity indoors not above the specified ones.

Add pure water to the dry mixture in an amount indicated in specifications, then mix it (use electric drills with screw socket). Leave closed mix for 5 minutes, and then stir again. The closed mix is suitable for use within 120 minutes (at recommended atmospheric conditions). Apply the closed mix ТМ MASTER. SATENPRO on the surface with a trowel or a float. Make movements perpendicular to each other. Remove plaster remains by moderate pressing the trowel at an angle to the surface being faced.

Rub with the sandpaper or wash off by wet-on-wet method with a layer thickness of 3 mm 60 minutes after application of the mix.

When arranging the multi-layer coating, each subsequent layer of plaster must be applied after drying of the previous one (after 24 hours).

NOTE TO A BUYER

- The base strength must be not less than the strength of the mix;

- Failure to follow the instructions for use mentioned on the package may adversely affect the aesthetic and performance properties;

- Products are not subject to mandatory certification;

- The mix is safe for human health in the production, transportation, storage, application and during the operation subject to following the requirements of this standard to production safety and health;

- Keep away from children;

- Date of manufacture, shelf life and batch number are mentioned on the package;

- Use only for the intended purpose.

- The manufacturer is not responsible for the use of the material for the purpose and under conditions not covered by this instruction.

- This instruction is a recommendation and does not substitute the professional training of the contractor.

Dry building mix ТМ MASTER GV.SHG1 white DSTU B V.2.7-126:2011

Ingredients

Mix of gypsum and mineral fillers, modified by polymeric additives

Size of aggregate, maximum

0.3 mm

Time the mix is suitable for use

120 minutes

Strength of adhesion to base

0.3 MPa

Limit strength in compression

5 MPa

Recommended layer thickness

3 mm

Recommended amount of water for preparing the mix

0.45 L / 1 kg of mix

Consumption

1 kg / m2 / 1 mm

All of these recommendations are efficient at +200С and relative humidity of 60%.

SAFETY RULES

When using the mix, use the personal protective equipment (respirator and rubber gloves). When working, protect the skin and eyes. In case of a mixture contact with eyes, rinse them immediately with plenty of water and seek medical advice.

Expiration date: 6 months from the date of manufacture mentioned on the package.

Must be disposed of in accordance the State Standard of Ukraine DSanPiN 2.2.7.029

Storage conditions: Store in the original intact packaging, on pallets, in dry premises at temperatures below +400С and humidity not more than 75%.

Warranty period: The manufacturer guarantees compliance of the quality with the requirements of this standard for the period specified on the package, provided the requirements of transport and storage are followed.